Get The Most Updated NACE-CIP2-001 Dumps To CIP Level 2 Certification
NACE Certified NACE-CIP2-001 Dumps Questions Valid NACE-CIP2-001 Materials
The Level 2 certification is an intermediate-level designation that requires a significant amount of training and experience. Candidates must have a minimum of two years of experience working in the coatings industry or a related field, as well as completion of the NACE CIP Level 1 certification program. This ensures that only qualified candidates are taking the exam and that the certification is held to a high standard.
To be eligible to take the NACE-CIP2-001 exam, candidates must have a minimum of two years of experience in coating inspection, and must have completed NACE-CIP1 (Coating Inspector Level 1) certification. NACE-CIP2-001 exam consists of 135 multiple-choice questions and lasts for 6 hours. It covers a wide range of topics, including surface preparation, coating application, inspection techniques, corrosion control, and health and safety.
NEW QUESTION # 51
When working with someone who is very concerned about Stability and maintaining adherence to the status-quo, the Inspector should try to:
- A. Implement immediate to get them motivated
- B. Challenge their value to the team and try to get them out of their comfort zone
- C. Give them as much advance notice as possible about upcoming changes
- D. Make sure they are the center of attention in all site meetings
Answer: C
NEW QUESTION # 52
When performing inspection in accordance with ASTM D 4138 the Inspector will use:
- A. A hardness tester
- B. A destructive paint inspection Tooke gauge
- C. A set of 14 pencils of varying hardness
- D. A mechanical adhesion tester
Answer: B
NEW QUESTION # 53
You are NACE Level 2 Inspector working on a tank lining job where a mobile centrifugal blast unit is being used to blast the tank floor to a NACE No.1/SSPC SP 5. The Contractor has completed his final blast and has called for a hold point inspection. This is the 1 st time you have seen field based centrifugal blast cleaning. You observe what appears to be staining on the substrate however the Contractor assures you this is normal when using centrifugal blast units and what you are seeing is what is defined in the standard as an acceptable variation in appearance.
Your FIRST preferred course of action is to:
- A. Shut the job down
- B. Review the standard with the Contractor and re-inspect the floor
- C. Call your supervisor
- D. Request that the Contractor re-blast the floor
Answer: B
NEW QUESTION # 54
When ASIN D 3363 is specified the Inspector must:
- A. Use the correct solvent
- B. Record the percentage of failure
- C. Record the two end points identified in the standard
- D. Record the highest value attained
Answer: C
NEW QUESTION # 55
You are a NACE Level 2 in-house inspector working in a shop. Your in-house requires you to perform a sleeve test to test for soluble salts; however the 3 rd party NACE Level 3 inspector, the owner, has a san smart meter and has achieved a very different result and has rejected the pre-cleaning.
Your FIRST course of action is to:
- A. Advise the other inspector he is using an incorrect method
- B. Redo the pre-cleaning based on the other inspectors results
- C. Review the specification with the other inspector to see what method was specified
- D. Advise your QC Manager to change the ITP to the use of the salt smart meter
Answer: C
NEW QUESTION # 56
When a coating is expected to be exposed to temperatures above 93C (200 F) the best choice would be:
- A. Organic coatings
- B. Polyurea
- C. Inorganic Coatings
- D. Latex
Answer: C
NEW QUESTION # 57
When performing an adhesion test in accordance with ASTM D 3359 where the Dry Film Thickness is approximately 10 mils, the Inspector should use:
- A. Method A - Cross Hatch
- B. Method B - Cross Hatch
- C. Method B - X cut
- D. Method A - X Cut
Answer: D
NEW QUESTION # 58
The cost of qualified Coating Inspection is normally offset by:
- A. Lower Safety Enforcement Costs
- B. Lower Supervision Costs
- C. Lower Coating Life Cycle Costs
- D. Lower Application Costs
Answer: C
NEW QUESTION # 59
NACE International Standards are developed by:
- A. International mandates
- B. Standard committees
- C. Government mandates
- D. Regional mandates
Answer: B
NEW QUESTION # 60
WJ-1 is always performed using UHWJ at pressures above 210 MPa (30,000 PSI)
- A. False
- B. True
Answer: B
NEW QUESTION # 61
Application of Thermal Spray Coatings requires:
- A. The same skills as welding
- B. The same skills as liquid coatings
- C. No particular skills
- D. Specialized skills supported by training and experience
Answer: D
NEW QUESTION # 62
When measuring the Dry Film Thickness Of liquid coatings applied to galvanized ferrous substrates the most commonly used instrument is the:
- A. Tooke Gauge
- B. Ultra Sonic DFT Gauge
- C. Magnetic Gauge
- D. Eddy Current Gauge
Answer: A
NEW QUESTION # 63
An Inspection and Test Plan is required when:
- A. It is always required
- B. When the Owner specifies one
- C. When the Coating Applicator requests one
- D. When the Inspector requests one
Answer: A
NEW QUESTION # 64
The primary purpose of Fireproofing coatings are to provide:
- A. Temporary protection for the structure
- B. fire extinguishing characteristics
- C. Preferential fuel for the fire
- D. Explosion resistance
Answer: A
NEW QUESTION # 65
Coating application to concrete substrates is:
- A. More challenging than coating steel
- B. Less challenging, than coating steel
- C. Not required as Concrete is inorganic
- D. The same as coating steel
Answer: A
NEW QUESTION # 66
You are the NACE Level 2 Inspector on a project where overcoating of galvanized steel is being performed. The specification references SSPC SP 16 as the surface preparation method. At the pre-job meeting operations personnel make it clear that abrasive blasting will not permitted. The Owner's representative asks you what other methods might be used.
Of the options shown below, what would be the preferred option in this situation?
- A. SP 1 followed by acid etching
- B. SP 1 followed by SP 3
- C. SP 1 followed by caustic etching
- D. SP 1 followed by SP 2
Answer: D
NEW QUESTION # 67
When completing the Final Inspection report the Inspector should write the report using:
- A. Language that the most would understand
- B. Language that another NACE Inspector would understand
- C. Language that only technical experts would understand
- D. Language that only in the project would understand
Answer: A
NEW QUESTION # 68
NACE/SSPC Water Jetting standards are directly equivalent to ISO Abrasive Blast Standards:
- A. False
- B. True
Answer: A
NEW QUESTION # 69
The solvent sensitivity/solvent wipe test (ASTM D4752) is used to determine the cure of
- A. urethanes.
- B. inorganic zincs.
- C. powder coatings.
- D. epoxies.
Answer: B
NEW QUESTION # 70
When environmental enclosures are being used an inspector needs to be concerned about:
- A. Lighting
- B. a), b), and c)
- C. Structural integrity
- D. Air changes
Answer: B
NEW QUESTION # 71
When performing a hardness test on a coating which has elastic properties the inspector is likely to likely to observe:
- A. No difference from any other coating
- B. A very low reading
- C. Cold flow or creep
- D. A very high reading
Answer: C
NEW QUESTION # 72
......
NACE-CIP2-001 Premium PDF & Test Engine Files with 100 Questions & Answers: https://examsboost.actualpdf.com/NACE-CIP2-001-real-questions.html
