Ultimate Guide to Prepare 300-510 Certification Exam for CCNP Service Provider in 2025
Use Real 300-510 Dumps - Cisco Correct Answers updated on 2025
Cisco 300-510 exam is part of the CCNP Service Provider certification track and serves as a prerequisite for the CCIE Service Provider certification. It covers a wide range of topics related to advanced routing solutions, including route manipulation, route redistribution, route filtering, and path control. Candidates are expected to have a deep understanding of the underlying routing protocols and their interaction with other networking technologies.
Cisco 300-510 exam is designed for IT professionals who specialize in service provider networking solutions. Implementing Cisco Service Provider Advanced Routing Solutions certification exam focuses on advanced routing solutions and covers topics such as implementing routing protocols, implementing MPLS VPNs, and implementing multicast protocols. By passing 300-510 exam, candidates will demonstrate their knowledge and skills in implementing complex routing solutions in a service provider environment.
NEW QUESTION # 117
What are three requirements for a static IPv6-in-IPv4 tunnel? (Choose three.)
- A. A static IPv4 address must be configured.
- B. A dynamic IPv4 address must be configured.
- C. A static IPv6 address must be configured.
- D. Cisco Express Forwarding must be enabled.
- E. A dynamic IPv6 address must be configured.
- F. Each tunnel endpoint must support IPv4 and IPv6.
Answer: A,C,F
Explanation:
NEW QUESTION # 118
Refer to the exhibit. Routers R1, R2. R3, and R4 have been configured to run OSPF. and router R5 is running EIGRP Traffic from R1 to R5 is expected to pass via R4. but OSPF routing has calculated the best path via R3.
Which action corrects the problem?
- A. Reconfigure R1 in Area 0.
- B. Configure R3 to use metric-type 1 with a higher metric than R4.
- C. Configure R1 with a static route to the R5 networks and set R5 as the next hop.
- D. Change the metric-type value on R3 to 2.
Answer: D
NEW QUESTION # 119
Refer to the exhibit.
P1 and PE3 Cisco IOS XR routers are directly connected and have this configuration applied. The BGP session is not coming up. Assume that there is no IP reachability problem and both routers can open tcp port 179 to each other. Which two actions fix the issue? (Choose two.)
- A. Remove the send and accept lifetime under key 1
- B. Change MD5 to HMAC-SHA1-12
- C. Change MD5 to SHA-1
- D. Change MD5 to HMAC-MD5
- E. Change MD5 to HMAC-ESP
Answer: B,D
NEW QUESTION # 120
Refer to the exhibit. A network engineer is configuring router R3 to handle multicast streams, but Host-2 cannot send subscription messages to the IPTV source. Which configuration must the engineer apply to router R3 so it passes the IPTV stream to Host-2?
- A. R3(config)# interface gigabitethernet 1/0/0
R3(config-if)# ip pim sparse-mode
R3(config)# interface gigabitethernet 1/0/1
R3(config-if)# ip pim sparse-mode
R3(config-if)# ip igmp version 3 - B. R3# configure terminal
R3(config)# no ip pim ssm default
R3(config)# interface gigabitethernet 1/0/0
R3(config-if)# ip pim sparse-mode
R3(config-if)# ip igmp version 3
R3(config-if)# ip pim ssm default
R3(config)# interface gigabitethernet 1/0/1
R3(config-if)# ip pim sparse-mode
R3(config-if)# ip igmp version 3
R3(config-if)# ip pim ssm default - C. R3# configure terminal
R3(config)# ip multicast-routing
R3(config)# interface gigabitethernet 1/0/0
R3(config-if)# ip pim sparse-mode
R3(config-if)# ip igmp version 3
R3(config)# interface gigabitethernet 1/0/1
R3(config-if)# ip pim sparse-mode
R3(config-if)# ip igmp version 3
R3(config-if)# ip pim ssm default - D. R3(config)# interface gigabitethernet 1/0/0
R3(config-if)# ip pim sparse-mode
R3(config-if)# ip igmp version 3
R3(config)# interface gigabitethernet 1/0/1
R3(config-if)# ip pim sparse-mode
R3(config-if)# ip igmp version 3
Answer: A
NEW QUESTION # 121
Refer to the exhibit.
Refer to the exhibit. Excessive routes are flooding from network 150.0.0.0 into AS100. Internet traffic between AS400 and AS300 is working normally. No route controlling mechanism is applied on incoming and outgoing traffic Which configuration resolves the issue?
- A. Option D
- B. Option C
- C. Option B
- D. Option A
Answer: D
NEW QUESTION # 122
Refer to the exhibit.
An engineer applied the summarization configuration on R1 for four networks (192.168.20.0/24 to
192.168.23.0/24) in area 1 and eight networks (192.168.32.0/24 to 192.168.39.0/24) in area 2 to stop the flooding of all the customer routes. While checking the routing table of R2, the engineer noticed that R1 is still sending only specific routes to R2. Which configuration should the engineer apply on R1 to summarize routes?
- A. Option D
- B. Option A
- C. Option C
- D. Option B
Answer: C
NEW QUESTION # 123 
Refer to the exhibit. Users connected to an application on 1.1.1.1 via routers CE1 and CE2 are complaining of frequent disconnections. While troubleshooting the issue, a network engineer with an employee ID: 4333:96:
916 determined that the application itself is working normally, but the link connected to the 1.1.1.1 application is flapping. The users on CE1 and CE2 are accessing applications on 2.2.2.2 without difficulty.
Which action resolves the issue?
- A. Disable split horizon on router R2.
- B. Redistribute CE1 routes on router R2.
- C. Enable route dampening on routers R1 and R2
- D. Enable passive interface on the router R3 Loopback1 interface.
Answer: C
NEW QUESTION # 124
Refer to the exhibit.
A network operator must inject a Level 1 route from XR2 (10.16.16.0/24) into the ISIS topology. Which configuration allows the injection in a way that XR3 and XR1 have a valid and working route for 10.16.16.0/24?
- A. Option D
- B. Option A
- C. Option C
- D. Option B
Answer: C
NEW QUESTION # 125
Refer to the exhibit.
An engineer applied the configuration on R1 to prevent network 192.168.1.0/24 from being propagated outside of area 5. After the change, users have reported they are not able to access any of the application servers that were working before. While checking the routing table of the peer router. The engineer notices R1 stopped propagating any routes outside are 5. Which action must be taken to fix the problem?
- A. Configure an additional filter-list on R1 for inbound traffic to allow external router into area 5.
- B. Add a permit statement for 0.0.0.0/0 le 32 to the end of the prefix-list 10 override the implicit deny.
- C. Change the prefix-list action to permit and add an explicit deny statement for network 192.168.1.0/24
- D. Reconfigure the filter-list statement to apply in the inbound direction
Answer: B
NEW QUESTION # 126
Refer to the exhibit.
Router 1 has established an SR-TE tunnel with router 2. Which statement describes this configuration?
- A. Router 1 and router 2 have a bidirectional tunnel set up with dynamic path selection.
- B. Router 2 is the head-end tunnel and has explicitly set a path to router 1.
- C. Router 1 is the head-end tunnel and has dynamically chosen a path to router 2.
- D. Router 1 has a list of labels used to explicitly lay out a path to router 2.
Answer: C
NEW QUESTION # 127
Compare different features between OSPFv2 and OSPFv3. Drag and drop the descriptions of OSPF from the left onto the correct OSPF versions on the right.
Answer:
Explanation:
NEW QUESTION # 128
For which reason do you deploy BGP confederations within a BGP transit backbone?
- A. to reduce the number of eBGP routes that must be shared between autonomous systems
- B. to increase the number of routes that can be redistributed between the running IGP and BGP
- C. to reduce the number of iBGP peering sessions
- D. to support a larger number of eBGP peer sessions
Answer: C
NEW QUESTION # 129
Refer to the exhibit.
XR1 and XR2 are sending the prefix 10.11.11.0/24 to XR3. A configured policy on XR1 is incorrectly prepending AS path 11 11 12 12 onto this prefix. A network operator wants to add a policy onto XR3 that will not allow the falsely prepending prefix from being installed. Which policy configuration applied to the XR3 neighbor configuration for XR1 can accomplish this requirement without impact to other or future received routes?
- A. Option C
- B. Option A
- C. Option B
- D. Option D
Answer: D
NEW QUESTION # 130
Refer to the exhibit.
Refer to the exhibit While troubleshooting a networking issue an engineer identified a suboptimal communication issue on route reflector RR2 In the current environment Router A is a non-route-reflector client for RR1 and RR2 Routers D and E are directly connected iBGP peers.
Router F is not an iBGP peer of routers D and E
Which action resolves the issue?
- A. Enable next-hop-self for BGP peering on router D.
- B. Disable BGP Client-to-Client reflection on router RR2.
- C. Enable next-hop-self for BGP peering on router C.
- D. Remove the route-reflector configuration on router RR2.
Answer: C
NEW QUESTION # 131
Refer to the exhibit. A service provider technician is working on a multicast issue for a customer.
While checking the multicast table, the technician notices that no flags are present for the (1.1.1.1, 239.1.1.1) entry, yet flags are present for the (1.1.1.1, 232.1.1.1) entry.
Which factor might explain this issue?
- A. Only the default SSM range is permitted
- B. Only GLOP is permitted
- C. Only ASM is permitted
- D. Only the administratively scoped range is permitted
Answer: A
NEW QUESTION # 132
Which command is used to enable BIDIR-PIM under global configuration mode for Cisco IOS XE Sofware?
- A. ip multicast-routing
- B. ipv4 pim bidir-enable
- C. ip pim bidir-enable
- D. ip pim bidir
Answer: C
Explanation:
Explanation/Reference: https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/ipmulti_pim/configuration/xe-3s/imc-pim-xe-3s- book/imc_basic_cfg.html
NEW QUESTION # 133
Refer to the exhibit. An engineer has configured all routers in the environment to run IS-IS Level 1 and Level 2 routing. The engineer wants traffic from R1 to R5 to pass via R2. but IS-IS routing has calculated the best path via R4. Which action corrects the problem?
- A. Set the link metric for the link from router R1 to router R4 to 30 or more.
- B. Configure routers R1, R2, and R5 for Level 1 routing only.
- C. Set the link metric on R2 for the links from router R2 to routers R3 and R4 to 30 or more.
- D. Configure routers R1, R4, and R5 for Level 2 routing only.
Answer: A
NEW QUESTION # 134
Which two characteristics unique to SSM when compared to ASM are true? (Choose two.)
- A. It uses (*,G) exclusively
- B. It uses RP
- C. It uses (S,G) exclusively
- D. It uses IGMPv3
- E. It uses SPT switchover
Answer: C,D
NEW QUESTION # 135
......
Cisco 300-510 exam covers a wide range of topics related to advanced routing solutions in a service provider network. These topics include BGP, OSPF, IS-IS, MPLS, Segment Routing, EVPN, VRF, and more. 300-510 exam also tests the candidate's ability to troubleshoot complex routing issues in a service provider network environment. 300-510 exam is designed to ensure that the candidate has a thorough understanding of the technology and is able to apply it in real-world scenarios.
CCNP Service Provider -300-510 Exam-Practice-Dumps: https://examsboost.actualpdf.com/300-510-real-questions.html
